Gas Filtration and Separation - Van Air Systems
Centro carries a complete online selection of gas filtration products to meet your needs. Whether you're looking for compressed air filtration or FRLs, we have the right product. Our gas vessels and coalescers...
Categories from Van Air Systems (1)
Desiccant Air Dryers
Desiccants in compressed air dryers remove moisture to protect equipment and ensure clean, dry air. Common types like activated alumina, silica gel, and molecular sieves adsorb water vapor as air passes through. This is vital in industries like food, pharma, and electronics. Desiccants require regular regeneration or replacement to maintain dryer efficiency and system reliability.
Filters
Filters
28 RESULTS
content loaded
MPN:33-0372
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$6,569.84
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0371
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,509.97
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0267
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$8,549.79
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0240
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$165.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0402
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,814.96
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0241
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$220.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0266
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$6,699.84
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0237
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
$145.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0401
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,499.97
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0372
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$6,569.84
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0371
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,509.97
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0267
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$8,549.79
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0240
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$165.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0402
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,814.96
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0241
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$220.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0266
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$6,699.84
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0237
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
$145.00
Loginto your account
Available for Purchase
Subject to factory lead times
MPN:33-0401
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
Sale Price:
$1,499.97
Loginto your account
Available for Purchase
Subject to factory lead times