Question 1

What types of electrical accessories are used in industrial control panels?

Accepted Answer

Industrial control panels rely on a range of electrical accessories to organize wiring, provide operator input, and indicate system status. Common categories include push buttons and selector switches for operator control, pilot lights and indicator lights for visual status feedback, terminal blocks for organizing and connecting field wiring, wire duct (also called wiring trunking) for routing and managing cables within the enclosure, DIN rail for mounting components, and cable glands and cord grips for securing cables entering the enclosure. These accessories may seem secondary to the main control devices, but they are essential for building a panel that is safe, organized, and maintainable.

Question 2

What is the difference between 22mm and 30mm push buttons and pilot lights?

Accepted Answer

The 22mm and 30mm designations refer to the panel cutout diameter — the size of the hole required to mount the device. 22mm is the current IEC standard and is the most widely used size in new industrial panel designs worldwide. 30mm is the traditional NEMA standard, still common in North American heavy-industrial and legacy panels. Functionally, both sizes offer the same types of operators — flush, extended, mushroom head, illuminated, and emergency stop — but 22mm devices are more compact, allowing more operators in a smaller panel footprint. When designing a new panel, 22mm is the standard choice unless the application requires the larger 30mm format for gloved-hand operation or compatibility with an existing panel cutout.

Question 3

What are terminal blocks and why are they important in panel wiring?

Accepted Answer

Terminal blocks are modular, insulated connectors mounted on DIN rail inside a control panel that provide a secure, organized connection point between field wiring and internal panel wiring. Instead of splicing wires together or landing every field wire directly on a device terminal, terminal blocks create a clean interface — field wires land on one side, and internal panel wires connect on the other. This makes troubleshooting, testing, and future modifications far easier because individual circuits can be disconnected and tested at the terminal block without disturbing the device wiring. Terminal blocks are available in screw-clamp, spring-clamp, and push-in styles, and in configurations for signal wiring, power distribution, grounding, fused circuits, and sensor connections.

Question 4

What is wire duct and how do I select the right size?

Accepted Answer

Wire duct (also called wiring trunking or cable raceway) is a slotted plastic channel mounted inside a control panel to route and organize wiring between components. The slots along the sides allow wires to exit the duct at any point along its length, providing clean access to terminal blocks, contactors, circuit breakers, and other devices. To select the correct size, the general rule is that wires should fill no more than 40–50% of the duct's cross-sectional area — this allows room for adding wires in the future and prevents excessive heat buildup. Duct is available in various widths and depths, and in standard slotted, narrow-slot, and solid-wall versions depending on the wire gauge and density of the application.

Question 5

What is an emergency stop (e-stop) push button and when is it required?

Accepted Answer

An emergency stop push button is a safety device that immediately de-energizes a machine or process when pressed by an operator. E-stops are typically large, red, mushroom-head buttons on a yellow background for high visibility, and they use a latching mechanism — once pressed, they stay locked in the off position until manually released by twisting, pulling, or using a key. This prevents accidental restart. OSHA and machine safety standards (such as NEMA ICS 6 and ISO 13850) require emergency stop devices on machinery where a hazard to personnel exists. E-stops must be wired into the safety circuit so that pressing the button removes power from all hazardous motion. They should be mounted in a location that is immediately accessible to the operator, and every machine should have at least one.

Electrical Accessories - SICK

$422.80

$845.60

$772.31

$65.10

$3,844.28

$3,844.28

$3,197.88

$3,197.88

$4,914.50

$4,914.50

$4,804.81

$4,804.81

$54.35

$354.34

$1,331.53

$68.03

$29.27

$91.98

$422.80

$845.60

$772.31

$65.10

$3,844.28

$3,844.28

$3,197.88

$3,197.88

$4,914.50

$4,914.50

$4,804.81

$4,804.81

$54.35

$354.34

$1,331.53

$68.03

$29.27

$91.98

Orders & purchases

Divisions