Compressed Air
Compressed air filtration and treatment removes dirt, water and oil so your air meets the quality that tools, instruments and products need. Clean, dry air reduces maintenance and protects downstream equipment.
...Categories in Compressed Air Filtration - Clean Air Solutions (7)
FRL's
FRLs (filter, regulator and lubricator units) condition compressed air at the point of use. They remove contaminants, set the correct pressure and add lubrication for pneumatic tools and components.
FRL Options
- Combination FRL units – three functions in one assembly
- Filter/regulators – space-saving two-in-one
- Modular units – build custom air prep assemblies
- Accessories – gauges, brackets, shutoff valves and drains
- Metal and polycarbonate bowls – match pressure and environment
Choosing an FRL
Size the unit for peak air flow and select filter micron and regulator range. Skip the lubricator if components are pre-lubricated or air must be oil-free. Metal bowls are required in some environments.
Centro carries FRL units and parts for compressed air systems.
Related categories: Compressed Air | Piping | Filter Vessel Assemblies | Dryers | Drains
Dryers
Compressed air dryers remove water vapor to prevent condensation, corrosion and freezing in air lines. Dry air protects tools, instruments and products, especially in painting, food and outdoor applications.
Dryer Types
- Refrigerated dryers – economical dew points around 35-39°F
- Desiccant air dryers – dew points to -40°F or lower
- Membrane dryers – point-of-use drying without power
- Heatless and heated regeneration – desiccant efficiency options
Choosing a Dryer
Select based on required pressure dew point, flow, inlet temperature and ambient conditions. Pre-filters protect desiccant dryers from oil. Size for summer conditions to avoid wet air.
Centro supplies compressed air dryers and replacement desiccant.
Shop by type: Desiccant Air Dryers
Related categories: Compressed Air | Drains | Piping | Oil Water Separators | FRL's
Filter Vessel Assemblies
Filter vessel assemblies are essential filtration solutions, designed to meet the demands of diverse industrial applications. Engineered for efficiency and reliability, these assemblies promises superior filtration performance across industries such as water treatment, oil and gas, chemical processing, and pharmaceuticals. With customizable configurations and high-quality materials, they provide robust containment for filter elements, optimizing filtration efficiency while minimizing maintenance downtime. Filter vessel assemblies are adept at handling a wide range of flow rates and operating pressures, delivering consistent and clean fluid output crucial for maintaining operational integrity and regulatory compliance. Embrace innovation and precision in filtration technology with filter vessel assemblies through us. Browse our selection below or contact us for a product expert to help you in your selection.
Related categories: Compressed Air | FRL's | Piping | Dryers | Drains
Drains
Compressed air drains remove the condensate that collects in filters, dryers, receivers and drip legs. Removing water automatically protects equipment and keeps air quality up.
Drain Types
- Timer drains – simple, programmable discharge
- Zero air-loss drains – discharge water only, saving energy
- Float drains – mechanical, no power needed
- Internal filter bowl drains – automatic draining at filters
Choosing a Drain
Consider the condensate volume, pressure, power availability and oil content. Zero-loss drains pay back quickly by stopping wasted air. Route condensate to an oil-water separator before disposal.
Centro carries compressed air drains for filters, receivers and dryers.
Related categories: Compressed Air | Oil Water Separators | Dryers | Parts and Accessories | Piping
Filter Elements
Compressed air filter elements are the replaceable parts that do the filtering inside compressed air housings. Regular replacement keeps air quality high and pressure drop low.
Element Types
- Particulate elements – remove solids
- Coalescing elements – remove oil and water aerosols
- Activated carbon elements – remove oil vapor
- OEM interchangeable elements – fit major brands
Replacement Tips
Replace elements annually or when pressure drop rises. Have the housing brand and model ready to find the right element.
Centro supplies compressed air filter elements.
Related categories: Compressed Air | Compressor Parts | Blowguns | Parts and Accessories | Oil Water Separators
Parts and Accessories
Compressed air parts and accessories keep air systems running efficiently. Replacement elements, gauges, fittings and service kits maintain filters, dryers and drains.
Parts & Accessories
- Filter elements – replacement cartridges for housings
- Service kits – seals, valves and drains
- Gauges and indicators – pressure and differential pressure
- Fittings and couplers – connections and quick disconnects
- Hose and reels – point-of-use distribution
Maintenance Tips
Replace filter elements at least annually and check drains regularly. Fixing leaks in fittings and hoses cuts compressor energy costs.
Centro supplies compressed air parts and accessories.
Related categories: Compressed Air | Blowguns | Oil Water Separators | Filter Elements | Drains
Compressor Parts
Compressor parts keep air compressors running efficiently. Regular replacement of filters, separators and wear parts protects the compressor and lowers energy costs.
Parts Available
- Air intake filters – protect compressor elements
- Oil filters and separators – rotary screw maintenance
- Valves and gaskets – reciprocating compressor repairs
- Belts and couplings – drive components
- Lubricants – compressor oils
Ordering Parts
Have compressor make, model and serial number ready. Follow service intervals for best efficiency.
Centro supplies compressor parts.
Related categories: Compressed Air | Filter Elements | Blowguns | Parts and Accessories | Oil Water Separators
Filter
Filter
5,282 items
content loaded
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$6,569.84
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,509.97
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$8,549.79
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$165.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,814.96
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$220.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$6,699.84
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
$145.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,499.97
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$190.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$200.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$190.00
Available for Purchase
Subject to factory lead times
ACS SAFETY VALVE;1/4 125 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/4 150 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/4 175 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 1in;FEMALE (CROWSFOOT)
$7.09$8.84
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 3/4in;FEMALE (CROWSFOOT)
$5.25$8.40
Low Stock (3)Ships within 1 business day
ACS TWIST LOCK 3/4in;MALE (CROWSFOOT)
$5.20$8.32
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 1/2in;FEMALE (CROWSFOOT)
$4.93$7.88
Low Stock (3)Ships within 1 business day
ACS TWIST LOCK 1/2in;MALE (CROWSFOOT)
$4.93$7.88
In Stock (7)Ships within 1 business day
ACS SAFETY VALVE;1/2 125 PS
$26.00$32.44
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/2 150PSI 2-J
$20.28$32.44
Low Stock (3)Ships within 1 business day
NEOPRENE 70+-5 DURO;GASKET MOLDED
$62.91
Should ship between 20 Nov and 04 Dec
Subject to factory lead times
The ASCO Series 342A stainless steel pressure filter/regulators are designed to meet the demands of harsh process environments. The series provides high flow rates with precise pressure regulation to actuators and ensures clean, dry media to eliminate contamination to downstream devices. Specifications include a 1/2" NPTF pipe size, with a stainless steel body material.
Requires Quote
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$6,569.84
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,509.97
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$8,549.79
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$165.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,814.96
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$220.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$6,699.84
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet
$145.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$1,499.97
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$190.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$200.00
Available for Purchase
Subject to factory lead times
Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)
$190.00
Available for Purchase
Subject to factory lead times
ACS SAFETY VALVE;1/4 125 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/4 150 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/4 175 PS
$6.18$9.88
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 1in;FEMALE (CROWSFOOT)
$7.09$8.84
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 3/4in;FEMALE (CROWSFOOT)
$5.25$8.40
Low Stock (3)Ships within 1 business day
ACS TWIST LOCK 3/4in;MALE (CROWSFOOT)
$5.20$8.32
Low Stock (1)Ships within 1 business day
ACS TWIST LOCK 1/2in;FEMALE (CROWSFOOT)
$4.93$7.88
Low Stock (3)Ships within 1 business day
ACS TWIST LOCK 1/2in;MALE (CROWSFOOT)
$4.93$7.88
In Stock (7)Ships within 1 business day
ACS SAFETY VALVE;1/2 125 PS
$26.00$32.44
Low Stock (1)Ships within 1 business day
ACS SAFETY VALVE;1/2 150PSI 2-J
$20.28$32.44
Low Stock (3)Ships within 1 business day
NEOPRENE 70+-5 DURO;GASKET MOLDED
$62.91
Should ship between 20 Nov and 04 Dec
Subject to factory lead times
The ASCO Series 342A stainless steel pressure filter/regulators are designed to meet the demands of harsh process environments. The series provides high flow rates with precise pressure regulation to actuators and ensures clean, dry media to eliminate contamination to downstream devices. Specifications include a 1/2" NPTF pipe size, with a stainless steel body material.
Requires Quote
Available for Purchase
Subject to factory lead times