Dryers

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Adsorbent Desiccant Brochure Activated Alumina - MSDS Sheet

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

Activated alumina is an aluminum oxide bead with an extremely porous structure and high surface area-to-mass ratio. Activated alumina has a wide variety of applications, including compressed air and gas drying. In compressed air and gas drying applications, activated alumina will achieve dew points -40°F to -100°F, depending on the dryer design. In compressed air desiccant dryers, a 1/8" (2-5 mm) activated alumina bead is most commonly used. The 1/4" (5-10 mm) activated alumina bead is typically used as a pre-bed for supporting large desiccant beds or as a buffer for silica gel beds. The 3/16" (5-10 mm) bead is used when pressure drop and surface area requirements fall between the 1/8" and 1/4" material. Features and Benefits High adsorption capacity for reducing initial cost, energy consumption, and operating costs Low abrasion for ensuring minimal dusting and a low pressure drop Resistant to liquid water slugging resulting from the failure of up stream after-coolers, separators, or drain traps. The adsorption capacity of the desiccant can be restored after complete regeneration. High crush strength for limiting dusting during loading of desiccant into dryer towers Uniform bead size minimizes pressure drop, channeling, and ensures utilization of the full desiccant bed In regenerative drying systems, Van Air activated alumina beds are sized for a service life of 2-5 years Available in 25lb pails, 50lb bags, 375lb steel drums and 2,000lb bulk bags Downloads Brochure Safety Data Sheet (SDS)

The Parker Balston 75-A20 is a Filtration Component. Precision-engineered component for Parker Balston compressed air and gas filtration systems. Parker Balston products are used across laboratory, pharmaceutical, semiconductor, and industrial applications for removing oil, water, and particulate contamination. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston 76-01 is a Filter Housing Accessory. Replacement bowl, guard, or accessory component for Balston filter housings. Maintains proper housing function and operator safety. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston 76-02 is a Filter Housing Accessory. Replacement bowl, guard, or accessory component for Balston filter housings. Maintains proper housing function and operator safety. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston 76-10 is a Filter Housing Accessory. Replacement bowl, guard, or accessory component for Balston filter housings. Maintains proper housing function and operator safety. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston 76-20 is a Filter Housing Accessory. Replacement bowl, guard, or accessory component for Balston filter housings. Maintains proper housing function and operator safety. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston 76-40 is a Filter Housing Accessory. Replacement bowl, guard, or accessory component for Balston filter housings. Maintains proper housing function and operator safety. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0002-40 is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0002-40-DX is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0008-40 is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0008-40-DX is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0010-35 is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.

The Parker Balston AD0010-35-DX is a Membrane Air Dryer. Combines coalescing filtration with membrane drying technology to deliver clean, dry compressed air with dewpoints as low as -40°F. Provides low-cost operation with minimal maintenance. Parker Balston is the recognized leader in compressed air and gas filtration technology, with products used across laboratory, pharmaceutical, semiconductor, and industrial manufacturing applications.